Testing and Measuring Instruments | Crescent Electric Supply Company

Amprobe

VP-440 Non-Contact Voltage Detector Probe, 50 to 1000 V AC, Light Indicator, CAT IV 1000 V

MFR: Fluke

MFR #: VP-440

UPC: 095969369312

Item #: 82897

Amprobe

TIC-300-PRO-KIT Non-Contact High Voltage Detector, 30 to 122000 V AC, Flashing Light/Beep Indicator

MFR: Fluke

MFR #: TIC-300-PRO-KIT

UPC: 095969915007

Item #: 1212703

Amprobe

Easily check and confirm proper wiring of electrical receptacles with this Receptacle Tester. Quickly confirm that GFCI breakers are properly wired for protection.

ST-102B GFCI Receptacle Tester, 110 to 125 V AC

MFR: Fluke

MFR #: ST-102B

UPC: 095969625005

Item #: 57075

Amprobe

If an industrial or utility testing application demands a higher level of safety, reach for this CAT IV rated Clamp Meter, the ACDC-3400 IND. Including true-rms sensing for accuracy this clamp on meter's extra large jaws can clamp on to those wide diameter wires making taking measurements in industrial environments simple.

ACDC-3400-IND AC/DC Digital True RMS Clamp-On Meter, 660 to 1000 A, 660 to 750 V AC, 660 to 1000 V DC, 660 mV AC/mV DC, 6.6 to 660 kOhm/6.6 to 66 MOhm, 50 to 500 Hz, 2 in Jaw, 3 Digits Backlit LCD Display

MFR: Fluke

MFR #: ACDC-3400-IND

UPC: 095969492683

Item #: 411689

Amprobe

ACD-10-PLUS AC/DC Digital Clamp Multimeter for Capacitance and Frequency

MFR: Fluke

MFR #: ACD-10-PLUS

UPC: 095969417457

Item #: 133310

Amprobe

AM-530 True-RMS Electrical Contactor Digital Multimeter

MFR: Fluke

MFR #: AM-530

UPC: 095969600392

Item #: 15067

Amprobe

Rugged and reliable for utility, industrial and mine safety applications, the TIC 300 PRO with VolTect is a Non-Contact, High Voltage Detector that verifies the presence of voltage in low, medium and high voltage test applications up to 122 kV without contacting the energized conductor.

TIC-300-PRO Non-Contact High Voltage Detector, 30 to 1500/1500 to 122000 V AC, LED Indicator

MFR: Fluke

MFR #: TIC-300-PRO

UPC: 095969497695

Item #: 56324

Hubbell Wiring Device - Kellems

Twist-Lock, Tester, 30A 125V, 2-Pole 3-Wire Grounding, L5-30P, Marine Version

HBLT26CM11 1-Phase 2-Pole 3-Wire Grounding Marine Standard Sized Circuit Tester, 125 V, 30 A Load

MFR: Hubbell Wiring Device-Kellems

MFR #: HBLT26CM11

UPC: 783585468679

Item #: 575012

Amprobe

If you install or connect 3-phase motors and systems, you recognize the importance of verifying the correct motor rotation and wiring phase sequence. Improper connections can cause motors to rotate in reverse direction, potentially damaging the motor and the equipment it is powering.

PRM-6 Phase Sequence and Motor Rotation Tester Motor Rotation-Phase Sequence Indicator, 700 V AC, Backlit LCD Display

MFR: Fluke

MFR #: PRM-6

UPC: 095969680288

Item #: 392321

Amprobe

AM-220 True-RMS AC/DC Clamp Meter, 600 Amp

MFR: Fluke

MFR #: AMP-220

UPC: 095969770866

Item #: 385200

Amprobe

AF-600 A-Frame Ground Fault Detector, Audio Indicator, CAT IV 600 V

MFR: Fluke

MFR #: AF-600

UPC: 095969873734

Item #: 1110949

Hubbell Wiring Device - Kellems

Straight Blade Devices, SNAPConnect Tester, Circuit Tester for SNAPConnect receptacle terminals, GFCI and standard receptacles

SNAPCTG 1-Phase 2-Pole 3-Wire 3-in-1 Standard Sized Receptacle Wiring Tester With GFCI Test Button, 125 V, 15/20 A Load

MFR: Hubbell Wiring Device-Kellems

MFR #: SNAPCTG

UPC: 783585555751

Item #: 710681

Hubbell Wiring Device - Kellems

Twist-Lock, Tester, 20A 277V AC, 2-Pole3-Wire Grounding, L7-20P

HBLT2331 2-Pole 3-Wire Grounding Circuit Tester, 277 V, 20 A Load

MFR: Hubbell Wiring Device-Kellems

MFR #: HBLT2331

UPC: 783585468617

Item #: 815710

Hubbell Wiring Device - Kellems

Twist-Lock, Tester, 20A 250V, 2-Pole 3-Wire Grounding, L6-20P

HBLT2321 2-Pole 1-Phase 3-Wire Grounding Standard Sized Circuit Tester, 250 V, 20 A Load

MFR: Hubbell Wiring Device-Kellems

MFR #: HBLT2321

UPC: 783585468594

Item #: 747188

Hubbell Wiring Device - Kellems

Twist-Lock, Tester, 30A 250V, 2-Pole 3-Wire Grounding, L6-30P

HBLT2621 2-Pole 1-Phase 3-Wire Grounding Standard Sized Circuit Tester, 250 V, 30 A Load

MFR: Hubbell Wiring Device-Kellems

MFR #: HBLT2621

UPC: 783585468600

Item #: 635734

Hubbell Wiring Device - Kellems

Twist-Lock Circuit Testers, 125V, 20Amp, Configuration NEMA L5-20P

HBLT2311 2-Pole 1-Phase 3-Wire Grounding Standard Sized Circuit Tester, 125 V, 20 A Load

MFR: Hubbell Wiring Device-Kellems

MFR #: HBLT2311

UPC: 783585468570

Item #: 747185

Amprobe

SM-20A Sound Meter, 31.5 Hz to 8 kHz, +/-1.5 dB, 0.1 dB Resolution, 4 Digits LCD Display, 125 ms/1 s Response

MFR: Fluke

MFR #: SM-20A

UPC: 095969499910

Item #: 1491322

Amprobe

CM100 Carbon Monoxide Meter, 25/30/35/45/50/70/100/200 ppm Detection, 1.5 V DC AAA Alkaline Battery, Backlit LCD Display

MFR: Fluke

MFR #: CM100

UPC: 095969463805

Item #: 1527544

Amprobe

AMB-110 Industrial High Voltage Insulation Resistance Tester, 0 to 600 V AC/DC, 425 kOhm, +/-5% RDG + 3 Digits, +/-15% RDG + 3 Digits Accuracy, LCD Display, CAT IV 600 V

MFR: Fluke

MFR #: AMB-110

UPC: 095969557016

Item #: 993217

Amprobe

AMB-55 Industrial High Voltage Insulation Resistance Tester, 0 to 600 V AC/DC, 300 kOhm, +/-5% RDG + 3 Digits, +/-15% RDG + 3 Digits Accuracy, LCD Display, CAT III 600 V

MFR: Fluke

MFR #: AMB-55

UPC: 095969557009

Item #: 130485

Amprobe

Test insulation of wires, cables, transformers and electrical motors quickly and easily with this rugged tester.

AMB-45 Insulation Resistance Tester, 600 V AC/DC, 4000 Ohm/400 MOhm, +/-1% RDG + 5 Digits Accuracy, LCD Display, CAT III 600 V, CAT II-1000 V

MFR: Fluke

MFR #: AMB-45

UPC: 095969366120

Item #: 55323

Amprobe

CO2-200 Carbon Dioxide Wall Mounted Meter, 0 to 9999 ppm Detection, NDIR Sensor, 12 V DC Adapter, LCD Display

MFR: Fluke

MFR #: CO2-200

UPC: 095969499347

Item #: 722428

Amprobe

Optimize the placement of solar systems and verify window efficiency. This measures solar output that is used to calculate overall energy, efficiency and placement of solar systems.

SOLAR-100 Solar Power Meter, 1999 W/sq-m/634 Btu/(sq-ft x h) Measuring, +/-10 W/sq-m +/-3 Btu/(sq-ft x h) or +/-5% Accuracy, 40 to 104 deg F, 3-1/2 Digits LCD Display

MFR: Fluke

MFR #: SOLAR-100

UPC: 095969499217

Item #: 128775

Amprobe

LAN-1 LAN Cable Tester, LED Display

MFR: Fluke

MFR #: LAN-1

UPC: 095969419345

Item #: 80876

Amprobe

PROF DMM TRUE RMS W OPTICAL PC INTERFACE

38XR-A Wireless Digital Multimeter, 750 V AC/1000 V DC, 10 A, 1 to 40000 kOhm, LCD Display

MFR: Fluke

MFR #: 38XR-A

UPC: 095969365413

Item #: 701430

Amprobe

TEST LEADS,ALLIGATOR CLIPS,HD DMMS, CAT IV 1000V

TL1500 Heavy Duty Test Lead, 1.5 kV AC, 250 mm OAL

MFR: Fluke

MFR #: TL1500

UPC: 095969362467

Item #: 577574

Amprobe

TMD-50 Digital Thermocouple Thermometer, K Thermocouple, 2 Inputs, -328 to 1999 deg F/-200 to 1372 deg C, +/-0.1% Accuracy, LCD Display

MFR: Fluke

MFR #: TMD-50

UPC: 095969556842

Item #: 397314

Amprobe

Infrared Thermometer, Temperature Range: -32 To 1050 DEG C, Focus Spot Size And Distance: 20:1, Accuracy: Plus/Minus1.8 PCT, Resolution: 0.1 DEG C/0.1 DEG F, Spectral Response: 8 - 14 UM, Laser Sighting: 630 - 670 NMTR, Response Time: 250 MS, Emissivity: 0.95, Repeatability: Plus/Minus0.5 PCT Of Reading Or Plus/Minus1 DEG F (Plus/Minus0.5 DEG C), Whichever Is Greater, Display: LCD, Included: Carrying Bag, Battery And Instruction Manual, Ambient Temperature Range: 0 - 40 DEG C, Battery Type: 9V (6F22 Alkaline), Memory Recall: Min/Max, Dimensions: 138 MM Length X 53 MM Width X 169 MM Height, Battery Life: 10 HR With Laser And Backlight On, 30 HR With Laser And Backlight Off

IR-720 IR-700 Infrared Thermometer, -26 to 1922 deg F, +/-1.8% RDG, 0.95, 9V Battery

MFR: Fluke

MFR #: IR-720

UPC: 095969614337

Item #: 939710

Amprobe

IR-450 3-in-1 Infrared Pocket Thermometer, -22 to 932 deg F/-30 to 500 deg C, +/-2 deg F, +/-1 deg C Accuracy, 0.95, AAA Battery

MFR: Fluke

MFR #: IR-450

UPC: 095969642552

Item #: 54683

Amprobe

RLD-1 Refrigerant Leak Detector, 3g/year, 15g/year, 30g/year R-22, 134a, 4g/year, 20g/year, 40g/year R-404A, 407C, 410A, For Use With R-22, 134a, R-404A, 407C and 410A Refrigerant

MFR: Fluke

MFR #: RLD-1

UPC: 095969499200

Item #: 704363

Amprobe

ACD-23SW True RMS Clamp-On Meter, 40 to 400 A, 4 to 600 V AC/DC, 400 mV DC, 400 Ohm/4 to 400 kOhm/4 to 40 MOhm, 50 to 500 Hz, 1.18 in Jaw, 3-3/4 Digits LCD Display

MFR: Fluke

MFR #: ACD-23SW

UPC: 095969563529

Item #: 322281

Amprobe

BAT-500 Battery Impedance Tester, Alkaline/Lead-Acid/Li-Ion/NiMH/NiCd Battery

MFR: Fluke

MFR #: BAT-500

UPC: 095969499187

Item #: 669539

Amprobe

True-Rms Navigator Clamp Meter, Voltage Rating: AC DC: 100 V, 1000 V, Amperage Rating: 100 AMP, 600 AMP, Frequency Rating: 20 HZ - 10 KHZ, Resistance: 1 KOHM, 10 KOHM, 100 KOHM, Capacitance: 400 MFD, 4 MILFD, Accuracy: Plus Minus (1.5 PCT RDG + 5 LSD) For AC current, Plus Minus (1.5 PCT RDG + 5 LSD) For DC Current, Plus Minus (1 PCT RDG + 5 LSD) For AC Voltage, Plus Minus (0.7 PCT RDG + 2 LSD) For DC Voltage, Plus Minus (1 PCT RDG + 3 LSD) For Resistance, Plus Minus (0.5 PCT RDG + 3 LSD) For Frequency, Plus Minus (1.9 PCT RDG + 8 LSD) For Capacitance, Display: Large 10,000 Count Display With Active Backlight And Analog, Temperature Rating: 0 - 10 DEG C, Battery: 9 V, Peak Hold: Yes, Diode Test: Yes, Dimensions: 238.3 MM Length X 87.3 MM Width X 51 Height, CE Certified, CAT IV 600 V , CAT III 1000 V Safety Standard, For professional Use

ACDC-52NAV Navigator AC/DC True RMS Clamp-On Power Meter, 100 to 600 A AC/DC, 100 to 1000 V AC/DC, 1 to 100 kOhm, 20 Hz to 10 kHz, 45 mm Jaw, Large Backlit LCD Display

MFR: Fluke

MFR #: ACDC-52NAV

UPC: 095969556651

Item #: 607349

Amprobe

Take this clamp meter to extremes. Most digital clamp meters have LCD screens that tend to freeze below 32 degrees (0 degrees Celcius) but the Amprobe RS-1007 PRO, an analog clamp meter can take extreme heat or cold and keep on measuring amps and volts-without problems or batteries.

RS-1007-PRO Analog Clamp-On Meter, 15 to 1000 A, 150 to 600 V AC, 1000 Ohm, 50/60 Hz, 1.9 in Jaw, Rotary Scale Display

MFR: Fluke

MFR #: RS-1007-PRO

UPC: 095969497725

Item #: 35794

Amprobe

Complete with a full range of diagnostic capabilities including phase sequence, power and power factor, total harmonics distortion and individual harmonics, inrush current and low pass filter, the Amprobe Navigator Clamp On Meter serves as a first line of defense for power monitoring and verifying system conditions before deploying more specialized tools -- or incurring additional costs. Rated CAT IV 600 V/CAT III 1000 V, these clamp on meters offer a new innovative navigation system that eliminates confusing push buttons, and replaces them with a single joystick. Its all about easy and reliable measurements. Amprobes new line of Navigator Clamp On Meters feature quick, easy to use single hand selection of measurements. The joy stick control allows quick selection of measurement features on the display from MAX -MIN to power factor to AC- DC current, with many more available. Simply highlight the desired measurement feature using the joy stick and press to select. Rugged and CAT IV reliable, this clamp on meter also features, super bright backlight display, built-in jaw flashlight and over mold bodies to absorb shock -- all you need for commercial and industrial environments.

ACDC-54NAV Navigator AC/DC True RMS Clamp-On Power Meter, 100 to 1000 A AC/DC, 100 to 1000 V AC/DC, 1 to 100 kOhm, 20 Hz to 10 kHz, 1.6 in Jaw, Large Backlit LCD Display

MFR: Fluke

MFR #: ACDC-54NAV

UPC: 095969556675

Item #: 160820

Amprobe

Low Current Clamp On Ammeter, Amperage Rating: AC DC: 4 AMP, 40 AMP, Frequency Rating: 40 HZ - 400 HZ In AC, Measuring Range: 0 - 40 AMP DC Or AC Peak, Operating Temperature: 0 - 50 DEG C, Dimensions: 184 MM Length X 71 MM Width X 31 MM Height, Battery Type: 9 V, Alkaline PP3, NEDA 1604, Display: 4000 Count,10 MM High Characters, Maximum Jaw Opening: 19 MM Cable, Maximum Jaw Opening: 20 MM, Accuracy: Plus-Minus (1.3PCT + 5 Digits), Temperature coefficient: Plus-Minus 0.05PCT Of RDG-DEGC, Resolution: 1 MILAMP In 4 AMP Range, 10 MILAMP In 40 AMP Range, Autoranging: 4 AMP-40 AMP, CE Certified, CAT III 300V

LH41A Digital Low Current Clamp-On Ammeter, 4 to 40 A, 40 to 400 Hz, 0.78 in Jaw, LCD Display

MFR: Fluke

MFR #: LH41A

UPC: 095969416542

Item #: 783715

Amprobe

This current transformer probe measures AC or DC current. It converts high current to a low level millivolt signal for input directly into a test instrument. It can be used with standard DMMs, recorders, digital or analog meters, data loggers/DAS, oscilloscopes, or other test and measurement instruments.

CT235A AC/DC Current Transformer Clamp, For Use With Standard DMMs, Recorders, Digital/Analog Meters, Data Loggers/DAS, Oscilloscopes or Other Test and Measurement Instruments, 1000 A

MFR: Fluke

MFR #: CT235A

UPC: 095969414586

Item #: 607872

Amprobe

AC50A AC Leakage Current Clamp-On Meter, 40 to 400 mA, 4 to 60 A, 400 V AC, 400 Ohm, 50/60 Hz, 40 Hz to 1 kHz, 1.2 in Jaw, 3-3/4 Digits LCD Display

MFR: Fluke

MFR #: AC50A

UPC: 095969416719

Item #: 764819

Amprobe

DGC-1000A Clamp-On Ground Resistance Tester, 10 A, Large Digital LCD Display, 9 V DC Battery

MFR: Fluke

MFR #: DGC-1000A

UPC: 095969366311

Item #: 194199

Amprobe

ACD-50NAV Navigator AC True RMS Clamp-On Power Meter, 100 to 600 A, 100 to 1000 V AC/DC, 1 to 100 kOhm, 20 Hz to 10 kHz, 45 mm Jaw, Large Backlit LCD Display

MFR: Fluke

MFR #: ACD-50NAV

UPC: 095969556637

Item #: 158794

Amprobe

AMP-25 AC/DC Mini-Clamp True RMS Clamp-On Meter, 60 to 300 A AC/DC, 1 in Jaw, Backlit LCD Display

MFR: Fluke

MFR #: AMP-25

UPC: 095969778787

Item #: 390952

Rittal Corp

9340280 Connection Pin, For OM Adaptor/Support, For Use With OM Adapter/Support, Insert Strip 9340.290, Polyamide (PA 6), RAL5010

MFR: Rittal

MFR #: 9340280

UPC: 639889830004

Item #: 75230

Amprobe

Contact And Non-Contact Tachometer, Range: Surface Speed (Contact): 0.1 - 1999 M MINT, 0.4 - 6550 FT MINT, Rpm Range: Rotation (Non-Contact): 1 - 99999 RPM: Rotation (Contact): 19 - 19999 RPM, Accuracy: Plus- Minus (0.02 PCT V Reading Plus- Minus1 Digit), Working Distance: 600 MM Maximum (Optical), Parts Included: 6 Adapters, Carrying Case, Reflective Tapes, Batteries And User Manual, Measuring Units: M, FT, IN, Dimensions: 175 MM Length X 60 MM Width X 28 MM Height, Battery: (2) AA1.5 V LR6 (Alakaline) Or Rechargeable, Operating Temperature: 0 - 50 DEG C, CE Certified

TACH20 Combo Tachometer, +/- 0.02% RDG, +/- 1 Digit Accuracy, 600 mm, Incandescent, Digital LCD Display

MFR: Fluke

MFR #: TACH20

UPC: 095969463881

Item #: 325700

Amprobe

Contact And Non-Contact Tachometer, Range: Surface Speed (Contact): 1 - 9999.9 M/MINT, 3 - 30,000 FT-MINT, 1 - 10,000 YD-MINT, Resolution: RPM Unit: 0.001,0.01,0.1,1, M-MINT Unit: 0.0001,0.001,0.01,0.1, Ft-MINT Unit: 0.0001, 0.001, 0.01, 0.1: YD-MINT Unit: 0.0001, 0.001, 0.01, 0.1, Rpm Range: Rotation (Non-Contact): 10 - 99999 RPM Rotation (Contact): 10 - 19999 RPM, Accuracy: Plus- Minus (0.1 PCT Of RDG + 2 Digit), Display: LCD With 15 MM Height X 33 MM Width, Working Distance: 5 - 30 CM (Non Contact), Parts Included: Meter, 9 V Battery, Cone And Funnel Contact Tips, Reflective Tape And Users Manual, Measuring Units: M, FT, YD, Dimensions: 266.6 MM Length X 177.8 MM Width X 81.28 MM Height, Battery: 9 V, Power Consumption: 5 MICAMP (Idle), 18 MILAMP (Measurement), Operating Temperature: 0 - 50 DEG C, CE Certified

TACH-10 Combo Tachometer, +/- 0.1% RDG, +/- 2 Digits Accuracy, 5 to 30 cm, Infrared, Digital LCD Display

MFR: Fluke

MFR #: TACH-10

UPC: 095969556699

Item #: 774607

Amprobe

Specifically designed for electrical, HVAC, mechanical, automotive applications with a temperature measurement range of 14 F to 932 F (-10 C to 500 C). Portable, ergonomic, and easy to operate, allows for quick and accurate identification of temperature related issues for electrical connections and motors, HVAC functionality and performance, and heat loss spots on the insulation around buildings to save energy costs.

IRC-110 Infrared Camera Thermal Imager, 14 to 932 deg F

MFR: Fluke

MFR #: IRC-110

UPC: 095969853835

Item #: 788040

Amprobe

This Anemometer with Flexible Precision Vane is ideal for HVAC technicians measuring heating, ventilation, air-conditioning, refrigeration, wind flow and temperature in residential, commercial and industrial air conditioning systems. It offers numerous functionsuse it to check air velocity FPM (feet per minute), air volume (flow) CFM (Cubic feet per minute) plus the remote vane allows greater measurement location flexibility. Switch between C and F. Input the area of airflow measurement to gain accurate air velocity results. Measure an air flow source for a continuous moving average for up to two hours. Determine minimum, maximum and average readings from a single point air source. Large dual display allows views of both air flow and velocity measurements plus temperature. Long extended flexible cord for remote vane access capabilities. All the measurements can be output to a computer for charting or analysis by optional model TM-SWA software and RS232 cable. Shipped in a deluxe hard carry case to protect and transport your Anemometer.

TMA10A Anemometer With Flexible Precision Vane, 0.4 to 25 m/s, +/-2% of Full Scale Accuracy, 32 to 122 deg F, Dual 4-Digits 9999 Counts LCD Display, 0.01 to 99.99 cu-m/s Flow Rate

MFR: Fluke

MFR #: TMA10A

UPC: 095969398886

Item #: 421277

Amprobe

TMA-21HW Hotwire Anemometer, 0.10 to 30 m/s, 0.2 to 110 kph, 10 to 6000 fpm, 0.10 to 59 Knots, 0.12 to 68 mph, +/-3% RDG +/-1% FS, 32 to 104 deg F, Triple 4-Digits LCD Display, 0 to 999900 cfm

MFR: Fluke

MFR #: TMA-21HW

UPC: 095969556910

Item #: 333274

Amprobe

TMA5 Mini-Vane Anemometer, 0.5 to 44.7 mph, 60 to 3937 fpm, 0.4 to 38.8 knot, 1.1 to 20.0 m/s, 0.7 to 72.0 kph, 1 to 8 BF, +/-5 % Accuracy, 32 to 122 deg F, LCD Display

MFR: Fluke

MFR #: TMA5

UPC: 095969516150

Item #: 129392

Filters